SMPTE/MIDI Time Code Sync (SMPTE/MTC) is another method of synchronization that lets Cakewalk act as a master or slave to external devices. Cakewalk can send or receive SMPTE/MTC messages to or from external devices that can generate or receive MTC. Cakewalk can send MTC on multiple output ports simultaneously.SMPTE/MTC is a position and timing reference that indicates the current location in the project and how quickly the project should be playing. Time code labels the position in a project in hours, minutes, seconds, and frames. The speed of playback is indicated by a frame rate.Time code is recorded onto tape using a device called a time code generator. The process of recording a time code signal onto a track is called striping. Normally, the start of a tape stripe has a particular time, expressed in hours, minutes, seconds, and frames. For example, the tape stripe might start at 00:00:00:00, 01:00:00:00, or any other time. The material recorded on the tape usually starts anywhere from 10 seconds to several minutes after the start of the time code. Sometimes, the tape stripe starts at a time like 00:59:50:00, and the material starts 10 seconds later, at 01:00:00:00.When you create a new Cakewalk project, by default the project is configured so that the beginning of bar 1 is synchronized with a time code of 00:00:00:00. If the starting point of the material on your tape or external project is not 0, you need to enter an offset to tell Cakewalk the time code that corresponds to the start of the project.
1. Go to Edit > Preferences > Project - Clock.
2. Specify the desired offset in the SMPTE/MTC Offset field. To enter an offset of 15 seconds, type 0,0,15 and hit ENTER. The SMPTE/MTC Offset value should now be 00:00:15:00 or 15 seconds.Seven time code frame rates are supported in Cakewalk, which are normally used for the following types of applications:
For more information about frame rate time formats, see the documentation for your time code hardware.Refer to the documentation for your MIDI interface or external MIDI device for additional information about SMPTE/MTC.
2. In the Control Bar’s Sync module, click the Sync Type button and choose Internal Sync or Audio Sync on the pop-up menu.
3. Go to Edit > Preferences > Project - MIDI.
4. Select the Transmit MTC check box (you can also click the Transmit MTC Sync button in the Sync module).
6. In the MTC Output Ports field, check off the outputs that you want to send MTC on (the outputs your external devices are connected to).
7. Click OK.Cakewalk saves your sync and MTC output port settings with your project. However, output ports are saved by their number only, not their name. Their number is determined by the order in which they appear in Edit > Preferences > MIDI - Devices. If you change the order of devices in this dialog box, the MTC output ports in your project will retain the same numbers, but those numbers will now refer to different outputs. Also, if you reduce the number of highlighted outputs in Edit > Preferences > MIDI - Devices, and the MTC ports you chose have higher numbers than what are currently highlighted in Edit > Preferences > MIDI - Devices, Cakewalk does not substitute new port numbers.
1. In the Control Bar’s Sync module, click the Sync Type button and choose SMPTE Sync on the pop-up menu.
2. Go to Edit > Preferences > Audio - Sync and Caching.
Ask first, then switch to clock source and start. This option prompts Cakewalk to alert you when it detects a SMPTE/MTC signal, asks if you want to sync to the incoming signal, and if you respond that you do, switches the clock source and starts to receive the signal.
Always switch the clock source and start. Cakewalk automatically switches to the clock source of the incoming signal and begins to receive the signal.
Do not switch clock source, but start if in SMPTE/MTC mode. This option automatically syncs to the incoming signal if Cakewalk is in SMPTE/MTC mode.
4. Click the Project - Clock page (Edit > Preferences > Project - Clock).
6. Click the MIDI - Devices page (Edit > Preferences > MIDI - Devices).
Note: If you want Cakewalk to switch its clock source to SMPTE/MTC automatically when Cakewalk receives a SMPTE/MTC signal, go to Edit > Preferences > Audio - Sync and Caching and select the Always switch clock source to start option.
Tip - Searching Documentation
Tip: To search for a specific topic, type your search query in the Search Cakewalk.com field at the top right of this page.
When the search results appear, click which product's documentation you would like to search to filter the search results further.
Note - Using Offline Help
Note: If you prefer to always use offline Help, go to Edit > Preferences > File > Advanced in your Cakewalk software and select Always Use Offline Help.
If you are not connected to the internet, your Cakewalk software will default to showing offline help until an internet connection becomes available.