The Process > Length and Process > Fit to Time commands can be used to stretch or shrink a portion of a project. Process > Length lets you stretch or shrink the selection by a fixed percentage and makes the adjustment by altering the individual events. A value of 200 percent, for example, stretches the selection to twice its original length, while a value of 50 percent shrinks the selection to half its original length.Process > Fit to Time stretches or shrinks the selection so that it ends at a specific time, expressed in either Measure:Beat:Tick (MBT) or Hours:Minutes:Seconds:Frames (SMPTE) format. This command gives you a choice of modifying the events or modifying the underlying tempo. This is useful when you want a portion of a project to have an exact length. The start time of the selection does not change, but the end time is altered as necessary to fit the required time interval.Both of these commands offer the option to stretch audio clips along with the MIDI information. Sometimes you don’t want to adjust the speed of your audio.
Audio can be stretched or condensed up to a factor of 4 (e.g., it can be shrunk to as little as 25 percent of its original length, or expanded to as much as 400 percent of its original length).You can also use the Process > Length command to alter only the start times or the durations of notes. For example, changing the durations of notes to 50 percent of their original length can create a staccato effect.
2. Choose Process > Length to display the Length dialog box.Figure 2947. The Length dialog box.
3. Choose to change the Start Times and/or Durations of selected notes by checking the boxes.
4. If you want to stretch selected audio clips, select the Stretch Audio check box. When this check box is enabled, the following option become available:
Type. Choose the type of audio data you're stretching. Choose options based on the source material: single voice or instrument versus a group of instruments (ensemble or polyphonic), and how long you want to wait for processing to finish: better quality can take a long time if you're processing several tracks.
6. Click OK when you are done.
2. Choose Process > Fit to Time to display the Fit to Time dialog box.Figure 2948. The Fit to Time dialog box.
3. Enter the desired end time in the New Thru box. Click Format to switch between MBT and SMPTE format.
Tempo Map. Choose this option if you want the tempo to change but not the duration of notes and events. For example, if your clip contains quarter notes, and you want those notes to stay quarter notes even though the elapsed time of the clip changes, choose Tempo Map. Cakewalk alters the tempo but not the events in the track.
Event Times. Choose this option if you want the tempo(s) to remain unchanged while note durations and event start times change.
5. If you want to stretch selected audio clips, select the Stretch Audio check box. The following option becomes available:
Type (disabled unless Stretch Audio is checked). Choose options based on the source material: single voice or instrument versus a group of instruments (ensemble or polyphonic), and how long you want to wait for processing to finish: better quality can take a long time if you're processing several tracks.
6. Click OK when you are done.
2. Do one of the following:
While dragging, a clip icon in the top right corner of the clip shows the stretch percentage (25% to 400%).
Note: You cannot stretch MIDI Groove clips. If you want to stretch a MIDI Groove clip, you must first either disable the clip’s Groove Clip Looping property (select the clip and press CTRL+L) or bounce the Groove clip to a new regular MIDI clip (use the Track view Clips > Bounce to Clip(s) command).
3. Do one of the following:
To stretch all notes proportionally. With the Smart tool , position the pointer where you want to split the note, then hold down the CTRL key and drag the end of any selected note.
To stretch all notes to the same absolute duration. With the Smart tool , position the pointer where you want to split the note, then hold down the SHIFT key and drag the end of any selected note.
Tip - Searching Documentation
Tip: To search for a specific topic, type your search query in the Search Cakewalk.com field at the top right of this page.
When the search results appear, click which product's documentation you would like to search to filter the search results further.
Note - Using Offline Help
Note: If you prefer to always use offline Help, go to Edit > Preferences > File > Advanced in your Cakewalk software and select Always Use Offline Help.
If you are not connected to the internet, your Cakewalk software will default to showing offline help until an internet connection becomes available.