SONAR LE Documentation is based on the full version of SONAR. Some screenshots, folder paths, features and other references may differ from your installation.
Click the Insert Module button in the Inspector and choose a module on the pop-up menu.
Right-click a module header or blank space in ProChannel and select Insert Module on the pop-up menu.Figure 307. Click the Insert Module button to insert a new module.
Right-click the module header and select Remove Module on the pop-up menu.Right-click a module header or blank space in ProChannel and select Replace Module on the pop-up menu.The signal flows from top to bottom. Click a module’s gripper and drag the module up/down to the desired position.Click a module to make it the active module. The active module is shaded slightly. You can use ACT to control parameters in the active module, and all context menu commands operate on the active module when right-clicking an empty space in ProChannel.
To specify the default configuration for tracks. Right-click any empty space in a track’s ProChannel and select Set Modules as Default for Tracks on the pop-up menu.
To specify the default configuration for tracks. Right-click any empty space in a bus’ ProChannel and select Set Modules as Default for Buses on the pop-up menu.By default, the ProChannel signal is routed prior to the channel’s effects bin (pre). To route ProChannel after the effects bin (post), right-click any empty space in ProChannel and select Post-FX bin on the pop-up menu.The QuadCurve Equalizer graph is divided into four sections, which correspond to the Low, Low-Mid, Mid-High and High bands. When you move the mouse pointer over the graph, the current band is highlighted.
To change the plot resolution globally, right-click any QuadCurve Equalizer graph in the Console view and choose the desired resolution on the pop-up menu. The resolutions are as follows:Figure 309. QuadCurve Equalizer graph.A. Low band B. Low-Mid band C. Mid-High band D. High band
2. Under Side Chain, click the On/Off toggle.
To load an existing preset, click the Load Preset button and navigate to the desired preset file.
To save a new preset or overwrite the current preset, click the Save Preset button , type a name, then click Save.
Note: To see the Load Preset and Save Preset buttons in the Inspector and collapsed Console view strips, hover the mouse over the Preset control.A. Current preset B. Load Preset C. Save PresetBy default, the Track Inspector dynamically updates to show the current track. However, you can choose to always show a specific instance of ProChannel regardless of which track is current.
2. Click the ProCh button at the top of the Inspector.
3. Click the Track Name control at the bottom of the Inspector and select Lock the current track or bus from the drop-down menu.To unlock the track or bus, select Lock the current track or bus from the menu again.
Table 176. ProChannel keyboard shortcuts ProChannel is only included with SONAR X3 Producer and Studio, not with the base version of SONAR X3. If a project was created in Producer or Studio and loaded into the base version of SONAR X3, the project might sound different because ProChannel is not available. However, if you resave the project in the base version of SONAR X3, all ProChannel settings will be persisted and available if you later load the project into Producer or Studio again.If you load a pre-SONAR X3 project that uses the per-channel Sonitus:fx EQ, the ProChannel QuadCurve Equalizer module will be disabled.If you want to keep and edit the Sonitus:fx EQ, double-click the small Equalizer graph in the collapsed ProChannel.To replace the Sonitus:fx EQ with the ProChannel QuadCurve Equalizer, do one of the following:
Tip - Searching Documentation
Tip: To search for a specific topic, type your search query in the Search Cakewalk.com field at the top right of this page.
When the search results appear, click which product's documentation you would like to search to filter the search results further.
Note - Using Offline Help
Note: If you prefer to always use offline Help, go to Edit > Preferences > File > Advanced in your Cakewalk software and select Always Use Offline Help.
If you are not connected to the internet, your Cakewalk software will default to showing offline help until an internet connection becomes available.