You can copy or move clips using drag-and-drop editing or the Cut, Copy, and Paste commands. If you copy or move clips into tracks that contain existing material, you need to let SONAR know how to combine the two.
When you use the Edit > Paste Special command to add information to a track that contains existing material, there is one final option you can choose.
Note that if you copy or move clips to new, empty tracks, you don’t have to worry about these settings. In this case, the track properties that go with the clips are automatically applied to the new track.
You can set the above options every time you perform an edit, or you can set them once and have the same settings carry over automatically. Check or uncheck the Ask This Every Time box in the Drag and Drop Options dialog box to indicate your preference. To open the Drag and Drop Options dialog box, click the Track view Options menu and choose Drag and Drop Options.
7. If necessary, choose the options you want from the Drag and Drop Options dialog box (go to Edit > Preferences > Customization - Editing, or right-click in the Clips pane and select Drag & Drop Options from the pop-up menu), and click OK.Figure 129. The Drag and Drop Options dialog box.
2. Choose Edit > Cut Special to display the Cut dialog box.Figure 130. The Cut dialog box.
3. Choose the options you want and click OK. SONAR cuts the clips from the project and places them on the Clipboard.
6. Choose Edit > Paste Special to display the Paste dialog box.Figure 131. The Paste dialog box.
2. Open the Clip Inspector and select the Properties section.
3. In the Time Format field, choose the units you want to use for the new start time and/or length by clicking one of the radio buttons:
M:B:T. Click this if you want the clip to begin and end on a specific measure, beat, or tick.
Samples. Click this is you want the clip to begin and end on a specific sample.
H:M:S:F. Click this is you want the clip to begin and end on a specific hour, minute, second, or frame. This is also known as SMPTE time, and lets you start the clip at an absolute-time-based (as opposed to musical-time-based) point in your project.
Seconds. Click this is you want the clip to begin and end on a specific second.
4. In the Start and Length fields, enter a new start time and/or length, or use the spinners or keyboard to change values.
5. Choose a value in the Time Base field—choose one of the two options in this section to control what happens to the clip’s start time when you change the tempo:
Musical (M:B:T). If the clip is set to the Musical time base, the clip’s M:B:T position stays constant, and its Absolute (SMPTE) position shifts.
Absolute (SMPTE). If the clip is set to the Absolute (SMPTE) time base, its Absolute position stays constant, and its M:B:T position shifts.
Note: The Snap Offset field is for audio clips only. The value of this field is the snap offset of the selected clip, in samples. When you set a snap offset value for a clip, and then drag the clip, the left edge of the clip does not snap to the current snap resolution--the clip snaps to a point on the clip that is the distance from the left edge of the clip to the snap offset value. For example, if you set the snap resolution to move to a measure, and the snap offset of a clip to 1500 samples, when you drag the clip, instead of the left edge of the clip moving to a measure line, the spot on the clip that's 1500 samples right of the beginning of the clip moves to the measure line.
7. If necessary, choose the options you want from the Drag and Drop Options dialog box, and click OK.
2. Choose Edit > Copy Special to display the Copy dialog box.
3. Choose the options you want and click OK. SONAR copies the clips to the Clipboard.
6. Choose Edit > Paste Special to display the Paste dialog box.
Choose Edit > Delete, which brings up a dialog box—choose options and click OK.
Tip - Searching Documentation
Tip: To search for a specific topic, type your search query in the Search Cakewalk.com field at the top right of this page.
When the search results appear, click which product's documentation you would like to search to filter the search results further.
Note - Using Offline Help
Note: If you prefer to always use offline Help, go to Edit > Preferences > File > Advanced in your Cakewalk software and select Always Use Offline Help.
If you are not connected to the internet, your Cakewalk software will default to showing offline help until an internet connection becomes available.